Greddy Emanage Blue Software Serial

Quite some time ago during some emission’s failures I sought a way to interact with my greddy emanage blue. I had tried other DIY’s but they were somewhat unclear and I never had results. Spravka o srednespisochnoj chislennosti rabotnikov obrazec rb.

Hey mike, i have just instaled a greddy emanage blue on my car and i bought the cable with the ecu, but my laptop doesnt have a serial port, so i got a serial to usb adaptor, but it wont communicate with my laptop. It just says offline?? Apr 5, 2010 - emanage: 1st Greddy E-manage Blue Mailing list. Then go to files and you can. Just make up any number for the serial number.

I set out to see the full picture and work with the right parts instead of hoping that a specific usb phone cable would be the part I was looking for. Here, and I must say I’m a bit late with this older system, I will try my best to provide a detailed description on the wiring and a guide on how to achieve the creation of this cable which would otherwise cost over 150$ USD from Greddy dealers.

The Greddy Emanage cable is NOT just a simple USB-USB, and it is also not the run of the mill usb-serial connector. What it really is, is described later. Guide Requirements: -Basic wiring/soldering skills -Laptop with Windows XP (or similar) -Willingness to buy parts from eBay (Rs232 TTL converter) -Spare USB cable to cut up (USB-A, the flat rectangular kind) Step 1 – Acquire Parts You will need a USB-A cable, just one end.

If you can, find an older piece of computer equipment you dont need (i.e. A mouse) and cut the end off, leave as much length as you can. The other piece of the puzzle is a 5-volt RS232 to TTL Converter. These are rather common and can be found locally if you have a good electronics shop, otherwise eBay works great. There are hundreds of these listed, often below $10.00 USD (shipping included). The standard serial port communicates with voltages levels -/+10v, however communication with the Emanage requires a range of 0-5v as it is a.

You will need one of these that will accept an operating voltage of 5 volts. Step 2 – Construct Strip your usb cable, there will be a foil and/or braided meshjust below the plastic. Using your hands pull this back and unravel it to reveal the four wires on the inside. They are most commonly coloured as red/black/white/green though can be any colour combination. You can simply cut off the mesh/foil shielding for this. Strip the end of every wire (very little needs to be showing, perhaps 2 or 3 mm. It’s time fire up the solder gun.

Look at your converter and find where the +5, Ground, tx and rx outputs are. They should be labelled or your part should have instructions. Here is where the USB connector wires should go to, use the chart and the image pinout of the usb to link it all together. USB Side Converter Side vcc +5V data – rx data + tx GND Ground Be sure to use a multimeter to check that you really have vcc, or gnd, etc before soldering into the board. Here is a picture of my end result: Step 3 – Software Emanage can be downloaded from this on yahoo. Sign up, and download e-manage149.EXE as well as v1.11.rar. Use winrar (provided on same group) to extract v1.11.rar then find and run the setup.exe.

Following that run e-manage149.EXE, it will ask for an extraction directory and defaults to a temporary directory. This must be changed, change this to an area such as c: temp. I’ve never found this update to install correctly, often failing with non-english errors. When that happens, exit out of it, and navigate to the directory where the files were extracted to. Copy all files except eUp.ini and eUp.exe.

Move these files over top of where you installed the management tool 1.11 (defaults to C: Program Files TRUST GReddy e-manage support tool). Step 4 – TUNE Plug the cable into your computer before loading the program. Turn on the car (ACC) and then start emanage. Once connected its all up to you.

The program may ask for a main unit update, in which case allow it to do so. If it prompts for a file, select the one that shows up in the dialog box or look for one within the emanage program directory. TROUBLESHOOTING / QUESTIONS I hope you don’t have to read this, fortunately I ran accross many problems and maybe I have a fix for you. The tool reports itself as online, but when I try to do anything it says “MAIN UNIT UPDATE” and “Corresponding Please Wait” I had this happen when the rx and tx wires were backwards. I’ve heard others having this problem, I think they just had the wires backwards.